Wendy and I have long dreamed of an intimate wine bar area somewhere in our house. While I have grand plans for a hidden and climate controlled wine storage area and tasting bar in the basement (many years down the road), the small area we've created in the kitchen will have to suffice until we can even begin to entertain grand plans similar to this.


Photo Credit: Vintage Makers

To tell you the truth, we're thrilled with how the small "wine bar" area in the kitchen has turned out. We love the cabinets, fridge, and counter tops, but the addition of the shelves we built and installed last week really brought the whole space home. But one of the items I thought long and hard about building is now my favorite aspect of our shelves and wine bar -- the inverted wine glass storage solution.

As I mentioned, I've thought about how to build this aspect of our shelves for quite some time. I have high hopes of being able to construct row upon row of wine glass storage in a tasting room area of the house, so this first go of my idea is more of a proof of concept or prototype for what will eventually come.

The end result of our efforts were so successful, and the cost so reasonable, I want to share the process with you so that you may be able to do the same, if you're so inclined.

Before you get started you're going to need some basic supplies. I built our storage racks using some stock oak flooring threshold and some oak trim I picked up at our local big box. If you have it available, and you're painting the finished product as we did, you could also use pine threshold so you don't need to worry about the grain showing through when painted. You'll also need a few wood screws and some glue.

Start by laying out the glasses you have on the bottom of the shelf. This will help you to properly define how many rows of glasses will work, how many deep you can place in each row, and a rough idea of where the center of the whole contraption will sit. If you can't just flip your shelf over (if you're trying to mount this on the underside of a cabinet or something else), just create a mock up of the underside of where you plan on mounting the glass racks so that you may obtain proper sizing.

In our case, we established that we'd be able to accommodate five rows of glasses, each holding approximately three wine glasses or two martini glasses. You can see how we laid this out with the shelf flipped over.

After we determined just how many glasses the shelf could accommodate and where the glasses would reside on the shelf, I got to work on the actual glass holders. The key to these holders is the way they allow the glasses to slide into the supports, and once in, are ultimately supported by the top side of the threshold. The tapered edge of the threshold pieces allow the slanted edges of the foot of the glasses to rest comfortably and securely, but the key is slightly raising the threshold to allow the base of each glass to sit completely within the threshold without being pinched. It's a little difficult to describe, but a photo of one half of a support should help demonstrate what I'm talking about.

My first step in actual construction was something that is purely optional. The threshold is actually much thicker than it needs to be for our application. Rather than allow it to hang down further than it needed to, I opted to trim the bottom 1/8" form the bottom of the threshold using our table saw. 

This not only reduced how substantial the threshold is, but it also trimmed off the grooves that are typically cut in the bottom of each threshold to prevent it from warping when it's used as an actual threshold. To trim this area I set the blade of the table saw to just over half the height of the threshold, then made two passes, one on each side. This took the bottom off rather nicely. I erred a bit on the side of caution and left a bit of the ridges on the bottom of the pieces and just figured I could sand them off later.

With the bottoms trimmed, I was able to cut the long lengths of threshold into individual pieces that are the correct size for the location where they will mount. We cut each into equal 11-1/2" lengths, the depth of each shelf. 

I used lengths of 2" x 1/4" oak trim to support the threshold and allow it to sit off the shelf a sufficient amount. In order to make sure there would be enough room on either side of these oak spacers for additional glasses, I ripped the oak trim down to 3/4" widths on the table saw.

Based on my measurements, the gap between each piece of threshold needed to be roughly 3/4" to allow our the stems to easily fit in the openings. At first, I second guessed my measurement and made the gap 1/2". As it turned out, I should have stuck with 3/4". If you're doing this at home, stick with 3/4" and you'll be safe.

I decided to affix the spacer trim pieces to the tops of the threshold pieces with a few 5/8" brad nails and a bead of glue along each pieces.

This allowed me to make each threshold its own single piece so I could mount them more easily to the bottom of the shelf. It's very important to establish the center line of each piece of threshold and trim. You can see in the photo below that the center lines, marked in pencil, line up with each other. If this isn't done you might end up with glasses fitting fine into one area, then not fitting at all into another.

I also made up the two side pieces of threshold wine glass support from a single piece of threshold. Since the side pieces only need to support wine glasses on one side, I ripped the pieces of threshold and spacer trim in half and nailed the spacers to the threshold as I had with the full pieces.

With all of the wine glass supports made up, I laid them out so I could establish all measurements that I needed to transfer onto the shelf.

I planned on attaching the threshold pieces to the shelf using two wood screws on each one, but I wanted to make it as clean and nice looking as possible. To accomplish this I determined consistent measurements where the screws would be located on each threshold, then drilled pilot holes and countersink reliefs where the screws would be able to sit without sticking out from the bottom of the threshold pieces.

I established the center point of the shelf and then transferred the measurements of the first two threshold pieces onto the bottom of the shelf. Clamping them to the shelf I attached each threshold pieces using the two 1-1/4" wood screws.

After the first threshold was in place, I used a 1/2" piece of wood between each piece to ensure a consistent spacing. As I said earlier, I should have used a 3/4" stock piece, but I didn't. Oh well, live and learn for when I do our giant wine bar.

Once all the pieces I had made up were attached to the bottom of the shelf, I was able to look at the end result of my work.

This is where I realized I should have made the gap 3/4". When this clicked in my head, rather than throw things around the basement and stomp around the house swearing at everything, I stayed calm (a major step forward for me). I trimmed the edges of the threshold using the router and gave myself that 3/4" gap I should have used. You can see in the photo below that I used a 1/8" plastic guide on the out feed of the router table. This let me trim just a bit without the wood getting chewed up by the router at the very end of the cut when it's no longer supported by that 1/8" that had been trimmed off.

After the edges were trimmed I re-attached the threshold/wine glass holders to the bottom of the shelf and took it for a nice test spin.

Once we were happy with the way the wine glasses fit in their openings, we disassembled the whole thing and I gave the undersides of the pieces of threshold a pretty major sanding with 40, 80, 120, and 220 grit sandpaper to get rid of any saw marks or noticeable swirls. After the sanding, we applied a coat of primer and two coats of paint to all of the threshold pieces. 

Reassembling the shelf after the paint dried gave us a great look at what we had built, and we were quite happy with the end results. 

After hanging the shelf on the wall we were finally able to do something we've been waiting to do for several years. We loaded our handful of wine glasses into the storage I had built beneath the shelves we had just constructed. Shortly after, Wendy worked her magic on the styling of the shelves. It was a personally triumphant moment, I assure you.

The threshold pieces are low enough profile that they don't hang down too far to be noticeable but they provide plenty of room for each glass. In all, it holds about 15 glasses, not a tremendous amount, but enough to be effective. What I did learn is that we can use this same approach in the eventual big time wine room we will some day build in our house. I have no idea when or where that will be, but I see it happening, and I see it looking awesome.

What do you think, is this a good approach for wine glass storage? How do you store your stemware? Do you have a custom solution to a storage challenge in your home? If so, we'd love to hear all about it. 

 

 

 

As seen on...

 

UndertheTableandDreaming

Comments 15

Comments

10/23/2012 at 10:56 PM
That looks awesome! I like the idea of the two fences on the router table at different measurements to prevent the ends from getting chewed up. I don't think I would have thought of that and would have ended up using choice words all the way to the big box store for more thresholds.
Alex
11/13/2012
The two fence trick is key when you are removing complete sections of material. I use that trick often.
10/24/2012 at 5:22 AM
I really love the wine glass storage rack you have made. Now how to get my husband make one also. Will be talking to him about this when he gets home.
Alex
11/13/2012
Just getting back to this comment now. How did the discussion go? Do you have wine glass storage now? :-)
FABBY
10/30/2012 at 10:50 AM
Fabulous! I love this shleves you created, with the wine rack incorporated in it..awesome! I'd like it in my kitchen! Thank you for sharing the tutorial.
FABBY
Alex
11/13/2012
Very glad you enjoy our approach. Thank you.
JC
10/30/2012 at 12:44 PM
Oh wow. Until I saw this post (just now), I thought you had bought pre-made tracks. It's probably much cheaper to make them yourself, but if you need a larger quantity, buying them pre-made might save a lot of time. I'm not sure where we got ours (we have over a dozen companies where we order parts and hardware), but we've installed tracks like these before. I think they also come in metal (stainless steel wire) also, but I'm not a fan of those.
Alex
11/13/2012
It's funny you mention the pre-made ones. As I was putting them together I was thinking "someone has to stock these already." It would have saved a lot of time, that's for sure.

We looked at the metal ones too, but I really don't like those options all that much.
lindsey
11/13/2012 at 10:03 AM
What did you use for lights? I'm not seeing any cords so did you find a good battery operated option? Any battery operated lights I've found in the past have been very flimsy and cheap - if you have a good source please share!

looks great, good job!
Alex
11/13/2012
Hi Lindsey,

We used an LED solution for the lights and we really like how it worked out. You can see more of it on this post www.oldtownhome.com/2012/10/5/Kitchen-Shelving-Part-2---Integrated-Wine-Glass-Storage-and-Lighting/ where we outline the various components and install.

You're right on the battery operated lights. I've yet to see one that lasts for any length of time that also looks good.

The lights we used are not cheap, but they work really well. I do wish they were dimmable, but the low profile nature of them won out over the dimmable version.
princelobga
12/13/2012 at 4:59 AM
It is just simple and nice. I love it.
I am a wood art lover and planning to try my hands woodworking for leisure. When I see fine woodwork like this, I am afraid, I feel as if I wont be able to venture into it.
Kudos
Wendy
12/14/2012
Go for it! Everyone has to start somewhere. We've made plenty of mistakes along the way, but that's how you learn and refine your skills. Good luck! :-)
Ryan
2/5/2013 at 8:44 PM
The overall transformation of "operation wine bar" is amazing and inspiring. So i had a few questions if you do remember?? Are your cleats for the shelves from end to end or just between the brackets? What size cleat did you use, and screws to mount them to the studs?
Alex
2/5/2013
Hi Ryan, thanks for the compliments. The cleats I used are just between the brackets for the upper two shelves, and then edge to edge on the lower shelf. The lower shelf was constructed slightly differently than the uppers, so the end to end just happened to work better there. For the studs I used 2" decking screws to secure the cleats, and then 1-1/4" wood screws form the tops of the shelves into the cleats. They've held strong so far.
Ryan
2/5/2013 at 10:38 PM
Thanks! Your write up was great and very detailed, just had a few questions.
Since you've not signed in yet, you will need to fill in your name and email below. If you have a Facebook account, save yourself a step and use Connect to login.

Denotes a required field.

Please enter full URL, including http://

You can use Markdown syntax in your comment. And you can also use lots of Emoji!
  • Search

  • Login
  • Follow
  • Advertising

If you're looking for information on advertising and sponsorships, head on over to our sponsorships page. You can purchase site sponsorships in a few easy clicks. 

Toolbox Tuesday
Open Housing
  • We're Featured!

Old Town Home has been featured in the following places and publications:

The Washington Post
 
Washingtonian Magazine
 
Domino
 
Old House Journal
 
 
Apartment Therapy House Tour
 
Washington Post Express Feature
 
Home & Garden Blogs
 
© 2024 OldTownHome.com. - Privacy Policy

Unexpected Error

Your submission caused an unexpected error. You can try your request again, but if you continue to experience problems, please contact the administrator.

Working...

Working...